The process optimization of the retention ring mold was highly involved; from the first part, it was clear a major redesign was in order. There was simply no way that the retention ring would fit within the outer diameter of the Yo-yo body and initially it was unclear as to whether this was the result of an error in design or in fabrication.
The design of the original retention ring mold had been dictated by the location of ejector pins. This aspect of the design worked very well, as there was no difficulty removing the finished part from the mold. Unfortunately, this also prevented any alteration of the diameter of the ring without designing an entirely new mold and ejection system. Despite the amount of work and machining this presented, it was decided that it would be better to make an alteration to the ring than it would to the body of the yo-yo, which would have to be expanded dramatically to accept the larger diameter ring.
We changed the mold to a thinner ring by decreasing the outer diameter, and installed a runner system to a larger diameter ejection ring that ran at a radius that transected the sprue (see figure below). The principle was that an outer ring of ejector pins would strike the removal ring, and in the process the retention ring at its center clear of the mold. Though this created visual defects in 3 places rather than one on the ring, it was of little concern as the outer walls of the ring would be hidden anyways.
From the first test, we observed a somewhat unexpected behavior. The thin outer ring intended to be struck by the ejector pins was cooling significantly more rapidly than the retention ring its self. This meant that for short cooling times, the ring had a tendency to stick to the cavity mold and would pull the retention ring most of the way clear, leaving the rest of the work to the sprue ejector pin. As cooling time increased, the retention ring began to hold more resolutely and removal became difficult. The thin runners to the outer ring would shear on impact, leaving the retention ring wedged. Accordingly we kept the cooling time at a relatively short 9 seconds, with a 4 second screw feed delay time.
Testing our finished retention ring, we found that we had underestimated the degree of shrinkage, and the ring dropped easily into the Body of the yo-yo. Luckily, this had been expected in our original design, and the interference provided by the body could be adjusted by a simple turning operation. The outer diameter of the body core mold was progressively turned down until a strong interference fit was achieved.
Pressing the ring was difficult, and required the added force of an arbor press. This was good, as it means that we will likely avoid the risk of spilling ball bearings even if the yo-yo were to be dropped or thrown.
With regards to the body, it was discovered later that an outdated drawing had been used to create the mold. This explained the original difficulty of fitting the ring. This also resulted in a string gap that was larger than expected, and a problem by which the string would slip next to the bearing and bind. Both of these problems were solved by inserting a small brass shim behind the magnet that was holding our nut guide into the mold. This decreased the string gap, and held the bearing in closer proximity to the sides of the yo-yo, preventing the string from slipping.
Ejection of the body with wider walls was initially disastrous due to the degree by which the walls clamped to the core mold. After trying a variety of cooling times ranging from 9-35 seconds, it was determined that slowing the ejector speed to 15%, and ejection force to 45% was sufficient to remove the part without either blowing out or severely deforming the back.
No changes were needed for the Spokes or the Cover.
Friday, April 24, 2015
Monday, April 6, 2015
Deliverable 2 for 3/6/2015: Retention Ring Details etc.
Hello There!
This post will be highlighting the work our team has completed on one part (the retention ring molds) and what we think will be our schedule and time frame moving forward with our YoYo.
Manufacturing Time Estimate
Other Molds and Optimization:
This post will be highlighting the work our team has completed on one part (the retention ring molds) and what we think will be our schedule and time frame moving forward with our YoYo.
Retention Ring Mold
Description:
The mold pieces for the retention ring have a fairly simple
design. The core has a depression that extends to the outer radius measurement
of the ring from the center of the stock. Also, this is where the gate is
located for the combined mold. The cavity also has this radius as it’s outside
most edge, but also has a circular section left blank by the lathe. This
creates the inner diameter for molding the ring piece. In addition to that, the
cavity mold has holes at the radius from the center to further assist in
removing the injection-molded part from the mold.
Cavity:
Core:
Shrinkage Calculation:
We measured and
found an average shrink of 10% of critical dimensions. Due to a geometric
limitation of ejector pin location, rather than scaling the yoyo up to shink to
our final design, we've decided to scale our entire design down by 10% to
accommodate the shrink of the retention ring.
We have started
our injection molding with the retention ring, so as to double check our
expected shrink, and proceed from there. These updates will be addressed in the
upcoming post.
Manufacturing process:
For the core, after the initial facing of the stock piece,
the outer stock of the piece is removed, leaving a centered circular extrusion.
This corner is then sharpened and two grooves are cut into the piece: one at the
outer edge and one at the inner edge of the ring. Next, the stock is moved to
the Mill and the center drill makes initial locator depressions for the ejector
pins, which are finally drilled out of the piece.
|
Step
|
Operation
|
Machine
|
Tool
|
Justification
|
|
1
|
Facing cut
|
Lathe
|
1
|
Leveling
and initial stock reduc-
tion
|
|
2
|
Facing cut
|
Lathe
|
1
|
Removing
outer stock
|
|
3
|
Rough cut
|
Lathe
|
9
|
Sharpen
inner corner for Reten-
tion
Ring
|
|
4
|
Finish cut
|
Lathe
|
8
|
Cut
groove for outer edge for
Ring
|
|
5
|
Finish cut
|
Lathe
|
7
|
Cut
groove for inner edge for
Ring
|
|
6
|
Drill
|
Mill
|
13
|
Center
Drill for location place-
ment
|
|
7
|
Drilling
|
Mill
|
17 Drill
|
Drill
Ejector Pins
|
For the cavity, once the piece has been faced, the center
depression is removed and smoothed over. Grooves are then created on the inner
and outer edges of what will be the retention ring.
|
Step
|
Operation
|
Machine
|
Tool
|
Justification
|
|
1
|
Facing Cut
|
Lathe
|
1
|
Leveling and initial shock reduction
|
|
2
|
Rough Cut
|
Lathe
|
10
|
Cutting to depth of cavity
|
|
3
|
Finish Cut
|
Lathe
|
10
|
Smoothing of cavity body
|
|
4
|
Finish Cut
|
Lathe
|
7
|
Create a groove on the inner side for retention ring
|
|
5
|
Finish Cut
|
Lathe
|
8
|
Create a groove on the outer side for retention ring
|
|
Process
|
Time
|
Units
|
|
Machining
|
x
|
Hours
|
|
Turning
|
3
|
Hours
|
|
Molding
|
2.5
|
Hours
|
|
Forming
|
1.7
|
Hours
|
|
Assembly
|
1.7
|
Hours
|
|
Total
|
x
|
Hours
|
Time
estimates were generated as a mix of Mastercam time estimates and
educated
estimation from research. Mastercam produces time estimates based
on
its generated toolpaths, and additional multiples of constant time were added
for
each tool change necessary during the fabrication of a part. This was less
time
for turning operations, as the tools are pre-loaded on the turret. Injec-
tion
moulding time was determined through research and discussion with Dave.
It
was assumed that injection time and cooling time scaled linearly with the
volume
of the part, while ejection remained constant. An additional hour per
injected
part was allotted for tuning tuning the process, with respect to injec-
tion
pressure, packing time, cooling time, and temperature.
Thermoforming
was assumed to be a constant time process of 1 minute, in-
cluding
heating and application of vacuum. Assembly was similarly assumed
based
o_ of process complexity, though as the operator becomes more skilled,
the
times are expected to drop. There is the possibility of some additional ma-
chining
to tune parts, but this should be absorbed in some of the extra time.
The
estimated time should not change the schedule of the team, though there
is an
incentive to start machining as quickly as possible.
Currently,
we do not anticipate much reworking to be done for our molds as we already
scaled them for the retention ring shrinkage. All time estimates currently
stand where we have them before.
Spokes Core and Cavity
- Key Details
- Not split down the center but where the initial fillets ended on one side.
- Bottom and top face fillets removed to decrease milling time and make mold possible to create
Yoyo Body cavity and core
- Key details
- As mentioned before, Body and the parts were scaled down 10% to match up to spokes.
As of right now, the team is working on optimizing the retention ring and will soon move on to optimizing the other pieces. These advances will be discussed in our next post. Until next time!
~Walking The Dog Yoyo Team
Subscribe to:
Posts (Atom)




