This post will be highlighting the work our team has completed on one part (the retention ring molds) and what we think will be our schedule and time frame moving forward with our YoYo.
Retention Ring Mold
Description:
The mold pieces for the retention ring have a fairly simple
design. The core has a depression that extends to the outer radius measurement
of the ring from the center of the stock. Also, this is where the gate is
located for the combined mold. The cavity also has this radius as it’s outside
most edge, but also has a circular section left blank by the lathe. This
creates the inner diameter for molding the ring piece. In addition to that, the
cavity mold has holes at the radius from the center to further assist in
removing the injection-molded part from the mold.
Cavity:
Core:
Shrinkage Calculation:
We measured and
found an average shrink of 10% of critical dimensions. Due to a geometric
limitation of ejector pin location, rather than scaling the yoyo up to shink to
our final design, we've decided to scale our entire design down by 10% to
accommodate the shrink of the retention ring.
We have started
our injection molding with the retention ring, so as to double check our
expected shrink, and proceed from there. These updates will be addressed in the
upcoming post.
Manufacturing process:
For the core, after the initial facing of the stock piece,
the outer stock of the piece is removed, leaving a centered circular extrusion.
This corner is then sharpened and two grooves are cut into the piece: one at the
outer edge and one at the inner edge of the ring. Next, the stock is moved to
the Mill and the center drill makes initial locator depressions for the ejector
pins, which are finally drilled out of the piece.
|
Step
|
Operation
|
Machine
|
Tool
|
Justification
|
|
1
|
Facing cut
|
Lathe
|
1
|
Leveling
and initial stock reduc-
tion
|
|
2
|
Facing cut
|
Lathe
|
1
|
Removing
outer stock
|
|
3
|
Rough cut
|
Lathe
|
9
|
Sharpen
inner corner for Reten-
tion
Ring
|
|
4
|
Finish cut
|
Lathe
|
8
|
Cut
groove for outer edge for
Ring
|
|
5
|
Finish cut
|
Lathe
|
7
|
Cut
groove for inner edge for
Ring
|
|
6
|
Drill
|
Mill
|
13
|
Center
Drill for location place-
ment
|
|
7
|
Drilling
|
Mill
|
17 Drill
|
Drill
Ejector Pins
|
For the cavity, once the piece has been faced, the center
depression is removed and smoothed over. Grooves are then created on the inner
and outer edges of what will be the retention ring.
|
Step
|
Operation
|
Machine
|
Tool
|
Justification
|
|
1
|
Facing Cut
|
Lathe
|
1
|
Leveling and initial shock reduction
|
|
2
|
Rough Cut
|
Lathe
|
10
|
Cutting to depth of cavity
|
|
3
|
Finish Cut
|
Lathe
|
10
|
Smoothing of cavity body
|
|
4
|
Finish Cut
|
Lathe
|
7
|
Create a groove on the inner side for retention ring
|
|
5
|
Finish Cut
|
Lathe
|
8
|
Create a groove on the outer side for retention ring
|
|
Process
|
Time
|
Units
|
|
Machining
|
x
|
Hours
|
|
Turning
|
3
|
Hours
|
|
Molding
|
2.5
|
Hours
|
|
Forming
|
1.7
|
Hours
|
|
Assembly
|
1.7
|
Hours
|
|
Total
|
x
|
Hours
|
Time
estimates were generated as a mix of Mastercam time estimates and
educated
estimation from research. Mastercam produces time estimates based
on
its generated toolpaths, and additional multiples of constant time were added
for
each tool change necessary during the fabrication of a part. This was less
time
for turning operations, as the tools are pre-loaded on the turret. Injec-
tion
moulding time was determined through research and discussion with Dave.
It
was assumed that injection time and cooling time scaled linearly with the
volume
of the part, while ejection remained constant. An additional hour per
injected
part was allotted for tuning tuning the process, with respect to injec-
tion
pressure, packing time, cooling time, and temperature.
Thermoforming
was assumed to be a constant time process of 1 minute, in-
cluding
heating and application of vacuum. Assembly was similarly assumed
based
o_ of process complexity, though as the operator becomes more skilled,
the
times are expected to drop. There is the possibility of some additional ma-
chining
to tune parts, but this should be absorbed in some of the extra time.
The
estimated time should not change the schedule of the team, though there
is an
incentive to start machining as quickly as possible.
Currently,
we do not anticipate much reworking to be done for our molds as we already
scaled them for the retention ring shrinkage. All time estimates currently
stand where we have them before.
Spokes Core and Cavity
- Key Details
- Not split down the center but where the initial fillets ended on one side.
- Bottom and top face fillets removed to decrease milling time and make mold possible to create
Yoyo Body cavity and core
- Key details
- As mentioned before, Body and the parts were scaled down 10% to match up to spokes.
As of right now, the team is working on optimizing the retention ring and will soon move on to optimizing the other pieces. These advances will be discussed in our next post. Until next time!
~Walking The Dog Yoyo Team





No comments:
Post a Comment