Blog 4
1.1 Final Yo-Yo
Below is a photo of our final yo-yo. The inner spokes and bearings were inspired by an perpetual motion wheel while the body was designed to be sleek and minimalist. Some key features include a clear cover that reveals the ball bearing moving inside, spokes held in place by locating pegs, and insert molded nuts in the body. We were happy with how the functionality of the retaining ring press fit and the locating pegs on the spokes turned out even after cooling. In future iterations, we could choose to make the body a different color, because the we had trouble completely purging the previous color and our white has a bit of an orangish tinge. It also shows dirt from manufacturing. We also could have used larger ball bearings, that would allow the yo-yo to function more as an infinite motion wheel.
1.2 Final Components
1.2.1 Retention Ring
The retention ring was made to hold the thermoformed cover in the body. It had a small fillet on the top surface both because of tooling specifications and aesthetic reasons. It took us two different iterations of machining to fine-tune the snap fit, but overall we were pleased with the final part fit and visible finish. Some minor improvements could be made to the surface finish on the sides of ring, which are hidden in the final assembly.
2 Table of Specifications
2.1 Table
2.2 Discussion
As can be seen from the table above, there was minimal error between the specified feature dimension, and the final dimension that was measured on the part. With regards to all of the injection moulded parts, it appeared that the expected shrinkage was greater than the shrinkage that eventually occurred, resulting in slightly oversize parts. Particularly with respect to the body and spoke interface, which was about 1/2 inch in diameter, it appears that shrinkage was almost entirely negligible. Numbers were closer on the retention ring, which was of a larger initial diameter, and therefore more susceptible to shrink. Due to a lack samples to measure and relatively loose design specifications, there was no attempt to guess what dimension the cover would shrink to. Consequently, the cover ended up being a fair degree smaller than was expected.
3 Retention Ring: In Depth
3.1 Summary of Findings
Since blog 3, the retention ring has changed dimensions to be thinner such that our press fit was tighter. The ejector pins now touched the part on an outer ring, which during optimization sometimes caused the retention ring to fail to eject properly. The retention ring experienced a change in cooling time from 9 seconds to 15 seconds for parts 61 - 70, which resulted in no detectible shift in either the part data or the Shewart Xbar chart to indicate that any change had occurred.
3.2 Link to PDF
1.1 Final Yo-Yo
Below is a photo of our final yo-yo. The inner spokes and bearings were inspired by an perpetual motion wheel while the body was designed to be sleek and minimalist. Some key features include a clear cover that reveals the ball bearing moving inside, spokes held in place by locating pegs, and insert molded nuts in the body. We were happy with how the functionality of the retaining ring press fit and the locating pegs on the spokes turned out even after cooling. In future iterations, we could choose to make the body a different color, because the we had trouble completely purging the previous color and our white has a bit of an orangish tinge. It also shows dirt from manufacturing. We also could have used larger ball bearings, that would allow the yo-yo to function more as an infinite motion wheel.
| Final assembled yo-yo, top view |
| Final assembled yo-yo, side view |
1.2.1 Retention Ring
The retention ring was made to hold the thermoformed cover in the body. It had a small fillet on the top surface both because of tooling specifications and aesthetic reasons. It took us two different iterations of machining to fine-tune the snap fit, but overall we were pleased with the final part fit and visible finish. Some minor improvements could be made to the surface finish on the sides of ring, which are hidden in the final assembly.
| Retention ring |
1.2.1 Body
The body was designed to be low profile and have multiple mating parts. The inner diameter of the wall press fits with the retention ring. The locating pegs and outer diameter of the hub help hold the spokes in place. We were pleased with how the locating holes aligned with the final injection molded spokes consistently, and that there was no detectable warping due to part thickness. In future iterations we would potentially make the outer wall thinner for aesthetic reasons and choose a different color that hides dirt better.
| Body |
1.2.1 Thermoformed Cover
The thermoformed cover was chosen to be clear so that the motion of the ball bearings inside would be visible. We were happy with the tolerances of how the outer diameter of the ring interacted with the retention ring to make an effective press fit. In future iterations, we would potentially make some design changes to make it easier to align on center every time.
| Cover |
1.2.1 Spokes
The spokes were designed to have cavities for the ball bearings to roll about freely in, and to mate with the body with both locating pegs to prevent rotation as well as a press fit in the center to align it on center every time. We were pleased with the accuracy of the dimensions of this part. In future iterations, we could modify the design to prevent warpage on the thicker areas where the spokes meet in the center.
| Spokes |
1.2.1 Ball bearings
We chose ball bearings based mainly on appearance, we wanted them to look cool and in proportion to the rest of the yo-yo. We were happy with how freely they rotate in the current design, and in future iterations could choose some with slightly more mass in order to make the infinite motion wheel more functional.
| Ball bearings |
1.2.1 Shaft Collar
The key feature of the shaft collar is that is rotates on the bearing but is a close enough press fit that the bearing will not shift dramatically and dislocate the string. We were happy with the final fit we achieved, but we could improve this element by speeding up the assembly time; we had chosen shaft collars that were slightly smaller than necessary so we had to first buckle and then crimp every one to get it to press fit with the bearing. In the future, we could choose a shaft collar with a slightly larger diameter.
| Shaft collar + bearing assembly. |
2.1 Table
2.2 Discussion
As can be seen from the table above, there was minimal error between the specified feature dimension, and the final dimension that was measured on the part. With regards to all of the injection moulded parts, it appeared that the expected shrinkage was greater than the shrinkage that eventually occurred, resulting in slightly oversize parts. Particularly with respect to the body and spoke interface, which was about 1/2 inch in diameter, it appears that shrinkage was almost entirely negligible. Numbers were closer on the retention ring, which was of a larger initial diameter, and therefore more susceptible to shrink. Due to a lack samples to measure and relatively loose design specifications, there was no attempt to guess what dimension the cover would shrink to. Consequently, the cover ended up being a fair degree smaller than was expected.
3.1 Summary of Findings
Since blog 3, the retention ring has changed dimensions to be thinner such that our press fit was tighter. The ejector pins now touched the part on an outer ring, which during optimization sometimes caused the retention ring to fail to eject properly. The retention ring experienced a change in cooling time from 9 seconds to 15 seconds for parts 61 - 70, which resulted in no detectible shift in either the part data or the Shewart Xbar chart to indicate that any change had occurred.
Retention Ring Run Chart
Retention Ring Histogram
Retention Ring Shewart x-bar chart
The UCL and LCL were found to be 2.228 inches and 2.180 inches respectively, and the mean was found to be 2.204 inches.
Retention Ring Process Capability
3.2 Link to PDF




No comments:
Post a Comment